Fingerprint Sensor

Product Code
:
18414
Brand / Origin
:
DFROBOT
Quantity
:
0
Without Vat
:
250.29 TL
Out of stock Alert when in stock
Same Day Shipping
If you purchase before 3pm, your products will ship at the same day. Except saturday and sunday
Add to Favorites
You can add this product on your list and check it later.
Add Comment
Featured Campaigns Related the Product

{{CMP.TITLE}}

{{CMP.DESCRIPTION}}

  • Features
  • Payment Options
  • Comments (0)
  • Recommend
  • Images
  • Suggestion Box
  • INTRODUCTION

    This is an Arduino compatible fingerprint module. With the high speed DSP processor, it could also work with other serial device, like MSP430, 51, AVR, PIC, STM32, ARM and FPGA device. This fingerprint module could work alone without any principal computer or any PC software. It could store 1000 fingerprint. Support fingerprint entry, intelligent image processing, fingerprint comparison and fingerprint search mode. It also has a high sensitivity to both wet and dry fingerprint recognition.

    This module could be widely used in security field, such as license management .etc. It can also be used to replace the IC card, password, hardware switch in your application.

    Turning On a Motorcycle Engine With Fingerprints

    Fingerprint Sensor Project 1: How to make a Fingerprint ID Nerf Gun

    My initial plans were to have the Arduino on the side with the power-pack and have the fingerprint ID scanner on the left side of the gun so that it can read the thumb print
    Hardware components:

    • Arduino Nano
    • Fingerprint Scanner
    • 9g 180° Micro Servo  

    how to make a fingerprint starter for bike


    Fingerprint Sensor Project 2: How to Make Fingerprint Lock for Your Computer


    Fingerprint Sensor Project 3: IoT Based Fingerprint Attendance System Using Evive

    This arduino project will show you how to make a DIY fingerprint attendance system.
    Hardware components

    Fingerprint Sensor Project 4: How to make a Fingerprint ID Nerf Gun

    My initial plans were to have the Arduino on the side with the power-pack and have the fingerprint ID scanner on the left side of the gun so that it can read the thumb print

    Hardware components
    • Arduino Nano
    • Fingerprint Scanner
    • Micro Servo
    • With additional parts from my stuff I have around:
    • Nerf N-Strike Elite Strife Blaster
    • Sugru
    • Generic Power Bank
    • Veroboard
    • General wires and things
    Fingerprint Sensor Project 5: How to make a Fingerprint Guarded Box
    Use DFRobot's UART fingerprint scanner to store fingerprints and only allow authorized people to access the box.
    Hardware components
    • DFRobot Fingerprint Sensor
    • DFRobot Particle Photon
    • 5mm LED

    Fingerprint Sensor Project 6: How to make Fingerprint Door Lock with Arduino 

    SPECIFICATION

    • Power supply: DC 3.8V-7.0V
    • Operating current: 65mA (Typical)
    • Interface: UART (TTL logical level)
    • Baud rate: (9600*N)bps, N=1~12(default N=6, 57600bps)
    • Image acquisition time: <1S
    • Storage capacity: 1000
    • FAR: <0.001%
    • FRR: <1.0%
    • Average searching time: <1s (1:500, average)
    • Matching Mode: comparison mode (1:1) and search mode (1:N)
    • Character file: 256 bytes
    • Template file: 512 bytes
    • Security level: 5(1,2,3,4,5(highest))
    • Working environment: Temp: -20°C - +60; RH: 40%-85%
    • Storage environment: Temp: -40°C - +85°C; RH: <85%
    • Touch area dimension: 14.5*19.4 mm (0.57*0.76")
    • Outline dimension: 54*20*20.5 mm (2.13*0.79*0.81")

    DOCUMENTS

    SHIPPING LIST

    • Fingerprint sensor x1
Prepared by  T-Soft E-Commerce.